# SBR and ABR RTMP Push Live with Edgecast - Proper PushPublishMap Syntax

**URL:** <https://community.wowza.com/t/sbr-and-abr-rtmp-push-live-with-edgecast-proper-pushpublishmap-syntax/34330>\
**Category:** Wowza Streaming Engine\
**Created:** [March 3, 2015, 11:57pm UTC](https://community.wowza.com/t/sbr-and-abr-rtmp-push-live-with-edgecast-proper-pushpublishmap-syntax/34330 "2015-03-03T23:57:40Z")\
**Posts on this page:** 2\
**Page:** 1

<div class="post-metadata">

**Author:** ![Clayton\_Bosquez](https://avatars.discourse-cdn.com/v4/letter/c/dc4da7/32.png) [@Clayton\_Bosquez](https://community.wowza.com/u/Clayton_Bosquez)\
**Post date:** [March 3, 2015, 11:57pm UTC](https://community.wowza.com/t/sbr-and-abr-rtmp-push-live-with-edgecast-proper-pushpublishmap-syntax/34330/1 "2015-03-03T23:57:40Z")

</div>

I have found one document suggesting proper mappings to push RTMP to Edgecast.

To push to EdgeCast, use the rtmp profile. The rtmp profile is pre-configured to push to an RTMP CDN. When pushing to EdgeCast, the following account information is required:

• Host

• ApplicationID

• StreamName

• Live Authentication Key

Following is an example entry to push the stream myStream to EdgeCast, assuming these credentials:

• Host: [fso.lax.0001.edgecastcdn.net](http://fso.lax.0001.edgecastcdn.net)

• ApplicationID: 200001

• StreamName: myStream

• Live Authentication Key: 0123456

My question is: What determines the ApplicationID, above listed as 200001?

Example map entry:

myStream={profile:“rtmp”, host:“[fso.lax.0001.edgecastcdn.net](http://fso.lax.0001.edgecastcdn.net)”, application:200001, streamName:“myStream?0123456”, originalTimecodeThreshold:0x100000}

Here is my mapping for Single Bit Rate. Can someone help me determine what I need to change?

#CDN2-SBR

livestream.stream\_360p={profile:“rtmp”, host:“[fso.lax.0001.edgecastcdn.net/Acct#](http://fso.lax.0001.edgecastcdn.net/Acct#)”, application:“default” streamName:“XXXXX-stream4?XKeyX&adbe-live-event=XXXXX”, originalTimecodeThreshold:0x100000}

Also, if I were to send three bitrates, 480p and 720p, what would be changed in the above??

Thanks!

Clayton

---

<div class="post-metadata">

**Author:** ![Michelle\_B](https://sea2.discourse-cdn.com/flex002/user_avatar/community.wowza.com/michelle_b/32/394_2.png) [@Michelle\_B](https://community.wowza.com/u/Michelle_B)\
**Post date:** [March 9, 2015, 3:26pm UTC](https://community.wowza.com/t/sbr-and-abr-rtmp-push-live-with-edgecast-proper-pushpublishmap-syntax/34330/2 "2015-03-09T15:26:01Z")

</div>

Hi Clayton,

The applicationID should be information that you get from Edgecast. Also, [multi-bitrate push publishing to edgecast](http://community.wowza.com/t/-/44724) was covered in a tutorial thread by one of our users. There should be no changes in the map settings except for the streamnames.

Michelle